100x300mm Welded Masonry Joist Hanger
100x300mm Welded Masonry Joist Hanger
Price: £12.24 (£14.69 inc VAT)
- Product Code: A1-5136
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model: WM100x300
- Weight: 1,273.00g
100x300mm Welded Masonry Joist Hanger
Width: 100mm
Height: 300mm
Weight: 1273g
100mm x 300mm Welded Masonry Joist Hanger is designed to support 300mm high timber joist. The joist hanger's actual height is 290mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to timber and timber to steel applications, where masonry flange should be securely fixed to the timber or to steel beams using appropriate fixings.
Installation of 100x300mm Welded Masonry Joist Hanger
- The back plate of the hanger should lie flat against the vertical masonry support,
- The masonry flange should never be placed in dry slots,
- Masonry flange should have a minimum of 3 courses (675mm masonry) above,
- Use correct strength mortar as per British Standard,
- Both supporting and above masonry should be allowed to mature before any load is applied,
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm,
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent,
- To provide lateral restraint HD Straps should be used,
- Use appropriate corrosion resistant fixings. Do not use galvanised fixings with stainless steel products or vice versa.
Specification
- Pre Galvanised Steel S280GD+Z275
- Also available in Stainless Steel
Certification
- Manufactured to EN 845 - 1:2013.
- Galvanised steel to EN10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088 - 2.
- Tested by CERAM Research Ltd Notification Body No.1289.
Masonry-Hangers_data_sheet.pdf
Brand: TECO
Model: TCSS 63mm M12
Delivery Time: In stock, 1-2 days
Diameter: 63mmTeeth Size: 1.2mm63mm M12 Single Sided Tooth Plate Timber Connector is designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity. The connectors are p..
£0.44
£0.53 inc VAT
Brand: TECO
Model: NKG
Delivery Time: In stock, 1-2 days
30x3.75mm Galvanised Square Twist Nails are ideal for fixing Joist Hangers. The twisted shank gives greater pull out values than a standard round wire nail. Approx. 400 nails per kilo in a bag. Nail directly into timber...
£4.50
£5.40 inc VAT
Brand: TECO
Model: WM44x250
Delivery Time: 2 - 4 days
44mm x 250mm Welded Masonry Joist Hanger is designed to support 250mm high timber joist. The joist hanger's actual height is 240mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to ti..
£4.26
£5.11 inc VAT
Brand: TECO
Model: TRS600B100
Delivery Time: In stock, 1-2 days
600mm bent 100mm Ron Sammons strap is a lightweight restraint strap that can be used instead of a traditional Heavy Duty Strap to provide lateral restraint of roof trusses, rafters and joists tied to masonry and for vertical applications such as holding down the wall plate. Designed to The Building ..
£1.09
£1.31 inc VAT
Brand: TECO
Model: LL - 132x450
Delivery Time: In stock, 1-2 days
132mm x 450mm Woody Long Leg Joist Hanger is produced from 1.5mm thick pre-galvanised mild steel produced in accordance to EN 10346 DX51D+Z275 with 50mm joist bearing. This timber to timber joist hanger designed for use in Loft Conversions where the hanger extends below the supp..
£6.36
£7.63 inc VAT
Brand: TECO
Model: WT-200/250
Delivery Time: In stock, 1-2 days
200mm Stainless Steel Housing Tie offers a practical and cost effective solution for masonry cavity walls in box form domestic dwellings of up to a maximum 10m in height. Used for cavities from 50mm to 70mm. Stainless Steel.Specification Fully tested to BS EN846-5:2000Meets the requirement..
£35.08
£42.10 inc VAT