125x100mm Welded Masonry Joist Hanger
125x100mm Welded Masonry Joist Hanger
Price: £4.45 (£5.34 inc VAT)
- Product Code: A1-5058
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model and Size: WM125x100
- Weight: 831.00g
125x100mm Welded Masonry Joist Hanger
125mm x 100mm Welded Masonry Joist Hanger is designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm. It is also suitable for many timber to timber and for timber to steel applications. The masonry flange should be securely fixed to the timber or to steel beams using appropriate fixings.
Installation of 125x100mm Welded Masonry Joist Hanger
- The back plate of the hanger should lie flat against the vertical masonry support,
- The masonry flange should never be placed in dry slots,
- Masonry flange should have a minimum of 3 courses (675mm masonry) above,
- Use correct strength mortar as per British Standard,
- Both supporting and above masonry should be allowed to mature before any load is applied,
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm,
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent,
- To provide lateral restraint HD Straps should be used,
- Use appropriate corrosion resistant fixings. Do not use galvanised fixings with stainless steel products or vice versa.
Specification
- Pre Galvanised Steel S280GD+Z275
- Also available in Stainless Steel
Certification
- Manufactured to EN 845 - 1:2013.
- Galvanised steel to EN10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088 - 2.
- Tested by CERAM Research Ltd Notification Body No.1289.
Masonry-Hangers_data_sheet.pdf
Brand: TECO
Model and Size: HM900
Delivery Time: In stock, 1-2 days
Galvanised Hex mesh Netting is used for floor screed reinforcement, wall plaster reinforcement and roof insulation. Also can be used for fencing. Made from hot dipped galvanised steel prior to weaving. Gloves should be worn as edges will be sharp.Hex mesh is formed by twisting two adjacent wires at ..
£52.73
£63.28 inc VAT
Brand: TECO
Model and Size: PB6/10
Delivery Time: In stock, 1-2 days
Plaster depth 6-10mm uPVC Plaster Angle Beads are designed for use externally where galvanised bead cannot be used or where they are preferred to stainless steel. They are also used internally in high moisture content areas or where pro longed drying out periods may be necessary. An impact..
£3.43
£4.12 inc VAT
Brand: TECO
Model and Size: WR44X250R100
Delivery Time: 2 - 4 days
44mm x 250mm Welded Return Joist Hanger is designed for similar applications and installation as the standard Masonry Joist Hanger. The return adds additional lateral support by wrapping around the back of the masonry or timber. The hanger has a 25mm drop on the return flange as standard, but a..
£4.98
£5.98 inc VAT
Brand: TECO
Model and Size: FHMR215
Delivery Time: 2 - 4 days
Single Piece Masonry Hanger Lock Plate is an additional element to use with the FHM Single Piece Joist Hanger and the WM Welded Masonry Joist Hanger. This plate is easily be transformed into a hook over joist hanger. No special tools or rivets are required. Just insert Lock ..
£1.35
£1.62 inc VAT
Brand: TECO
Model and Size: LD250F
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 250mm Flat is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres hol..
£0.61
£0.73 inc VAT
Brand: TECO
Model and Size: WT-225/250
Delivery Time: In stock, 1-2 days
225mm Stainless Steel Housing Tie offers a practical and cost effective solution for masonry cavity walls in box form domestic dwellings of up to a maximum 10m in height. Used for cavities from 50mm to 70mm. Stainless Steel.Specification Fully tested to BS EN846-5:2000Meets the requirement..
£36.11
£43.33 inc VAT