8mm Helical Bar Stainless Steel - 2m length
8mm Helical Bar Stainless Steel - 2m length
Price: £12.44 (£14.93 inc VAT)
- Product Code: A1-5514
- Delivery Time: In stock, 1-2 days
- Brand: TECO
- Model: HBH8/2000
- Weight: 160.00g
8mm Helical Bar Stainless Steel - 2m length
Length: 2000mm
Thickness: 8mm
Weight: 160g
8mm Helical Bar is used in a variety of applications; in general the metre lengths are used for crack stitching and reinforcing masonry in both new and existing masonry structures. The deformation of the fins makes the bonding characteristics of the Helical Bar far superior to alternative standard reinforcing materials. Stainless steel grade 304 (grade 316 available on request).
Features
- Grade 304 austenitic stainless steel (grade 316 available to order).
- Excellent bonding capabilities.
- Coiled spring properties within elastic limit.
- High stress material.
- No sudden or catastrophic failure point.
- Less intrusive than standard repairs.
Installation
- Rake or cut slots into horizontal mortar joint to a depth of between 25-35mm and a 450mm or 6 brick courses vertical spacing.
- Vacuum out the slots and thoroughly flush with water.
- Mix the two part Grout (HG3) in the tub provided.
- Insert a bead of Grout into the back of the slot using a grout gun.
- Push the Helical Bar into the Grout to obtain good coverage.
- Insert a bead of Grout over the exposed Helical Bar and iron into the slot using a finger trowel. Fill in the slot with Grout leaving sufficient depth for re pointing.
- Use a colour matched mortar to repair fractured bricks.
- Re-point the slot to match existing as closely as possible and make good the area.
- If in doubt, seek advice from a structural engineer.
Brand: TECO
Model: WM50x275
Delivery Time: 2 - 4 days
50mm x 275mm Welded Masonry Joist Hanger is designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm. It is also suitable for many timber to timber and for timber to steel applications. The masonry flange should be securely fixed to the timb..
£4.74
£5.69 inc VAT
Brand: TECO
Model: LD1200B100T
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 1200mm Bent 100mm Twisted 100mm is designed for vertical restraint, for example fixing wall plates to masonry and also for horizontal restraint. The straps are produced from edge coated galvanised mild steel, also available in stainless ..
£2.42
£2.90 inc VAT
Brand: TECO
Model: HD900B150
Delivery Time: In stock, 1-2 days
Galvanised Heavyt Duty Restraint Strap 900mm Bent 150mm is designed for lateral and horizontal restraint (as in roof trusses). The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres holes.APP..
£2.69
£3.23 inc VAT
Brand: TECO
Model: LL - 63x450
Delivery Time: In stock, 1-2 days
63x450mm Woody Long Leg Joist Hanger is produced from 1.5mm thick pre-galvanised mild steel produced in accordance to EN 10346 DX51D+Z275 with 50mm joist bearing. This timber to timber joist hanger designed for use in Loft Conversions where the hanger extends below the support.&..
£4.12
£4.94 inc VAT
Brand: TECO
Model: GBCLIP150/50
Delivery Time: In stock, 1-2 days
150mm Galvanised Gravel Board Clips for fitting gravel boards securely to timber fence posts. Width 55mm. Made from Galvanised Steel EN 10346 DX51D Z275. ..
£1.48
£1.78 inc VAT
Brand: TECO
Model: TCSS 63mm M12
Delivery Time: In stock, 1-2 days
Diameter: 63mmTeeth Size: 1.2mm63mm M12 Single Sided Tooth Plate Timber Connector is designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity. The connectors are p..
£0.46
£0.55 inc VAT