6mm Helical Bar Stainless Steel - 2m length
6mm Helical Bar Stainless Steel - 2m length
Price: £9.20 (£11.04 inc VAT)
- Product Code: A1-5512
- Delivery Time: In stock, 1-2 days
- Brand: TECO
- Model: HBH6/2000
- Weight: 120.00g
6mm Helical Bar Stainless Steel - 2m length
Length: 2000mm
Thickness: 6mm
Weight: 120g
6mm Helical Bar is used in a variety of applications; in general the metre lengths are used for crack stitching and reinforcing masonry in both new and existing masonry structures. The deformation of the fins makes the bonding characteristics of the Helical Bar far superior to alternative standard reinforcing materials. Stainless steel grade 304 (grade 316 available on request).
Features
- Grade 304 austenitic stainless steel (grade 316 available to order).
- Excellent bonding capabilities.
- Coiled spring properties within elastic limit.
- High stress material.
- No sudden or catastrophic failure point.
- Less intrusive than standard repairs.
Installation
- Rake or cut slots into horizontal mortar joint to a depth of between 25-35mm and a 450mm or 6 brick courses vertical spacing.
- Vacuum out the slots and thoroughly flush with water.
- Mix the two part Grout (HG3) in the tub provided.
- Insert a bead of Grout into the back of the slot using a grout gun.
- Push the Helical Bar into the Grout to obtain good coverage.
- Insert a bead of Grout over the exposed Helical Bar and iron into the slot using a finger trowel. Fill in the slot with Grout leaving sufficient depth for re pointing.
- Use a colour matched mortar to repair fractured bricks.
- Re-point the slot to match existing as closely as possible and make good the area.
- If in doubt, seek advice from a structural engineer.
Brand: TECO
Model: NP170x350
Delivery Time: In stock, 1-2 days
170x350mm Galvanised Nail Plate is plate used to connect or repair timber. The plate has strengthening ribs for added rigidity. All holes are pressed countersunk to aid location of the nail and to give a flush finish. Made from Galvanised steel EN 10346 DX51D Z275. InstallationUse appropri..
£86.86
£104.23 inc VAT
Brand: TECO
Model: LD1000F
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 1000mm Flat is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres holes.S..
£1.74
£2.09 inc VAT
Brand: TECO
Model: HI300P
Delivery Time: In stock, 1-2 days
Scrolled Hot Dipped Galvanised Hip Irons provide a decorative restraint when bedding hip tiles. Available in a range of sizes and finishes. InstallationDue to the angle of the roof along the hip, a Hip Iron is fixed at the bottom of the hip first to support the weight of the hip tiles so ..
£1.94
£2.33 inc VAT
Brand: TECO
Model: FHM47/150
Delivery Time: In stock, 1-2 days
47mm x 150mm Single Piece Joist Hanger are designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm. They are also suitable for many timber to timber applications by fixing the masonry flange securely to the timber or to steel beams using ap..
£2.54
£3.05 inc VAT
Brand: TECO
Model: TCSS 63mm M16
Delivery Time: In stock, 1-2 days
Diameter: 63mmTeeth Size: 1.2mm63mm M16 Single Sided Tooth Plate Timber Connector is designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity. The connectors are p..
£0.73
£0.88 inc VAT
Brand: TECO
Model: WR44X250R100
Delivery Time: 2 - 4 days
44mm x 250mm Welded Return Joist Hanger is designed for similar applications and installation as the standard Masonry Joist Hanger. The return adds additional lateral support by wrapping around the back of the masonry or timber. The hanger has a 25mm drop on the return flange as standard, but a..
£4.98
£5.98 inc VAT