90x225mm Welded Masonry Joist Hanger
90x225mm Welded Masonry Joist Hanger
Price: £5.18 (£6.22 inc VAT)
- Product Code: A1-5125
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model: WM90x225
- Weight: 1,050.00g
90x225mm Welded Masonry Joist Hanger
Width: 90mm
Height: 225mm
Weight: 1050g
90mm x 225mm Welded Masonry Joist Hanger is designed to support 225mm high timber joist. The joist hanger's actual height is 215mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to timber and timber to steel applications, where masonry flange should be securely fixed to the timber or to steel beams using appropriate fixings.
Installation of 90x225mm Welded Masonry Joist Hanger
- The back plate of the hanger should lie flat against the vertical masonry support,
- The masonry flange should never be placed in dry slots,
- Masonry flange should have a minimum of 3 courses (675mm masonry) above,
- Use correct strength mortar as per British Standard,
- Both supporting and above masonry should be allowed to mature before any load is applied,
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm,
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent,
- To provide lateral restraint HD Straps should be used,
- Use appropriate corrosion resistant fixings. Do not use galvanised fixings with stainless steel products or vice versa.
Specification
- Pre Galvanised Steel S280GD+Z275
- Also available in Stainless Steel
Certification
- Manufactured to EN 845 - 1:2013.
- Galvanised steel to EN10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088 - 2.
- Tested by CERAM Research Ltd Notification Body No.1289.
Masonry-Hangers_data_sheet.pdf
Brand: TECO
Model: HI300/5
Delivery Time: In stock, 1-2 days
Scrolled Hot Dipped Galvanised Hip Irons provide a decorative restraint when bedding hip tiles. Available in a range of sizes and finishes. InstallationDue to the angle of the roof along the hip, a Hip Iron is fixed at the bottom of the hip first to support the weight of the hip tile..
£3.09
£3.71 inc VAT
Brand: TECO
Model: HI300P
Delivery Time: In stock, 1-2 days
Scrolled Hot Dipped Galvanised Hip Irons provide a decorative restraint when bedding hip tiles. Available in a range of sizes and finishes. InstallationDue to the angle of the roof along the hip, a Hip Iron is fixed at the bottom of the hip first to support the weight of the hip tiles so ..
£1.94
£2.33 inc VAT
Brand: TECO
Model: ST150
Delivery Time: In stock, 1-2 days
Mild Steel Screw Ties are used to tie timber door and window frames to adjacent brickwork. Zinc and yellow passivated mild steel. Threaded one end. Screw directly into timber using a small pilot hole if required. - 5mm..
£35.00
£42.00 inc VAT
Brand: TECO
Model: MBS3x16
Delivery Time: In stock, 1-2 days
16mm Stainless Steel Movement Mesh Beads are used to overcome movement tolerances in plaster and render finishes minimising racking in finished coat. It can also be used to act as a stop barrier for when a change in finish is required or type of render finish. 3m length.Installation Use ap..
£22.31
£26.77 inc VAT
Brand: TECO
Model: FHMR47X125R115
Delivery Time: In stock, 1-2 days
The Masonry Return Joist Hangers are designed for similar applications and installation as the standard Masonry Joist Hangers. The return adds additional lateral support by wrapping around the back of the masonry or timber. They have a 25mm drop on the return flange as standard but many special..
£3.50
£4.20 inc VAT
Brand: TECO
Model: TCDS 38mm M10
Delivery Time: In stock, 1-2 days
Diameter: 38mmTeeth Size: 0.9mm38mm M10 Double Sided Tooth Plate Timber Connector is designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity. The connectors are p..
£0.29
£0.35 inc VAT