63x175mm Welded Masonry Joist Hanger
63x175mm Welded Masonry Joist Hanger
Price: £4.45 (£5.34 inc VAT)
- Product Code: A1-5107
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model: WM63x175
- Weight: 577.00g
63x175mm Welded Masonry Joist Hanger
Width: 63mm
Height: 175mm
Weight: 577g
63mm x 175mm Welded Masonry Joist Hanger is designed to support 175mm high timber joist. The joist hanger's actual height is 165mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to timber and timber to steel applications, where masonry flange should be securely fixed to the timber or to steel beams using appropriate fixings.
Installation of 63x175mm Welded Masonry Joist Hanger
- The back plate of the hanger should lie flat against the vertical masonry support,
- The masonry flange should never be placed in dry slots,
- Masonry flange should have a minimum of 3 courses (675mm masonry) above,
- Use correct strength mortar as per British Standard,
- Both supporting and above masonry should be allowed to mature before any load is applied,
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm,
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent,
- To provide lateral restraint HD Straps should be used,
- Use appropriate corrosion resistant fixings. Do not use galvanised fixings with stainless steel products or vice versa.
Specification
- Pre Galvanised Steel S280GD+Z275
- Also available in Stainless Steel
Certification
- Manufactured to EN 845 - 1:2013.
- Galvanised steel to EN10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088 - 2.
- Tested by CERAM Research Ltd Notification Body No.1289.
Masonry-Hangers_data_sheet.pdf
Brand: TECO
Model: WT-200/50
Delivery Time: In stock, 1-2 days
200mm Stainless Steel Housing Tie offers a practical and cost effective solution for masonry cavity walls in box form domestic dwellings of up to a maximum 10m in height. Used for cavities from 50mm to 70mm. Stainless Steel.Specification Fully tested to BS EN846-5:2000 Meets the requiremen..
£9.41
£11.29 inc VAT
Brand: TECO
Model: LD300F
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 300mm Flat is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres hol..
£0.53
£0.64 inc VAT
Brand: TECO
Model: MB3x12
Delivery Time: In stock, 1-2 days
12mm Galvanised Movement Mesh Beads are used to overcome movement tolerances in plaster and render finishes minimising racking in finished coat. It can also be used to act as a stop barrier for when a change in finish is required or type of render finish. 3m length.Specification Galvanised..
£21.35
£25.62 inc VAT
Brand: TECO
Model: WM100x200
Delivery Time: 2 - 4 days
100mm x 200mm Welded Masonry Joist Hanger is designed to support 200mm high timber joist. The joist hanger's actual height is 190mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to t..
£5.03
£6.04 inc VAT
Brand: TECO
Model: TRS1000B100
Delivery Time: In stock, 1-2 days
1000mm bent 100mm Ron Sammons strap is a lightweight restraint strap that can be used instead of a traditional Heavy Duty Strap to provide lateral restraint of roof trusses, rafters and joists tied to masonry and for vertical applications such as holding down the wall plate. Designed to Th..
£1.81
£2.17 inc VAT
Brand: TECO
Model: HI300/3
Delivery Time: In stock, 1-2 days
Scrolled Hot Dipped Galvanised Hip Irons provide a decorative restraint when bedding hip tiles. Available in a range of sizes and finishes. InstallationDue to the angle of the roof along the hip, a Hip Iron is fixed at the bottom of the hip first to support the weight of the hip tile..
£3.28
£3.94 inc VAT