63x275mm Welded Masonry Joist Hanger
63x275mm Welded Masonry Joist Hanger
Price: £6.18 (£7.42 inc VAT)
- Product Code: A1-5111
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model and Size: WM63x275
- Weight: 783.00g
63x275mm Welded Masonry Joist Hanger
Width: 63mm
Height: 275mm
Weight: 783g
63mm x 275mm Welded Masonry Joist Hanger is designed to support 275mm high timber joist. The joist hanger's actual height is 265mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to timber and timber to steel applications, where masonry flange should be securely fixed to the timber or to steel beams using appropriate fixings.
Installation of 63x275mm Welded Masonry Joist Hanger
- The back plate of the hanger should lie flat against the vertical masonry support,
- The masonry flange should never be placed in dry slots,
- Masonry flange should have a minimum of 3 courses (675mm masonry) above,
- Use correct strength mortar as per British Standard,
- Both supporting and above masonry should be allowed to mature before any load is applied,
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm,
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent,
- To provide lateral restraint HD Straps should be used,
- Use appropriate corrosion resistant fixings. Do not use galvanised fixings with stainless steel products or vice versa.
Specification
- Pre Galvanised Steel S280GD+Z275
- Also available in Stainless Steel
Certification
- Manufactured to EN 845 - 1:2013.
- Galvanised steel to EN10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088 - 2.
- Tested by CERAM Research Ltd Notification Body No.1289.
Masonry-Hangers_data_sheet.pdf
Brand: TECO
Model and Size: FHM50/100
Delivery Time: In stock, 1-2 days
50mm x 100mm Single Piece Joist Hanger are designed to support timber joists built in to brick or block walls with a minimum crushing strength of 3.5N/mm. They are also suitable for many timber to timber applications by fixing the masonry flange securely to the timber or to steel beams using ap..
£1.80
£2.16 inc VAT
Brand: TECO
Model and Size: TCDS 63mm M10
Delivery Time: In stock, 1-2 days
Diameter: 63mmTeeth Size: 1.2mm63mm M10 Double Sided Tooth Plate Timber Connector is designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity. The connectors are p..
£0.73
£0.88 inc VAT
Brand: TECO
Model and Size: HD1200T150
Delivery Time: In stock, 1-2 days
Galvanised Heavy Duty Restraint Strap 1200mm Twisted 150mm is designed for lateral and horizontal restraint (as in roof trusses). The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres h..
£3.39
£4.07 inc VAT
Brand: TECO
Model and Size: NUTFBZPM10
Delivery Time: In stock, 1-2 days
M10 Zinc Plated Hex Full Nuts for use with bolts and studding. InstallationAlways ensure that compatible corrosion resistant nuts & washers are used, i.e. do not use galvanised nuts & washers with stainless steel studding or vice versa...
£14.85
£17.82 inc VAT
Brand: TECO
Model and Size: TRS1600B100
Delivery Time: In stock, 1-2 days
1600mm bent 100mm Ron Sammons strap is a lightweight restraint strap that can be used instead of a traditional Heavy Duty Strap to provide lateral restraint of roof trusses, rafters and joists tied to masonry and for vertical applications such as holding down the wall plate. Designed to Th..
£2.90
£3.48 inc VAT
Brand: TECO
Model and Size: HD1200B100
Delivery Time: In stock, 1-2 days
Galvanised Heavy Duty Restraint Strap 1200mm Bent 100mm is designed for lateral and horizontal restraint (as in roof trusses). The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres holes.APP..
£3.39
£4.07 inc VAT