50x225mm R100mm Welded Return Hanger

50x225mm R100mm Welded Return Hanger
Price: £4.70 (£5.64 inc VAT)
- Product Code: A1-5294
- Delivery Time: 2 - 4 days
- Brand: TECO
- Model and Size: WR50X225R100
- Weight: 731.00g
50x225mm R100mm Welded Return Hanger
Width: 50mm
Height: 225mm
Thickness: 2.4mm
Weight: 731g
50mm x 225mm Welded Return Joist Hanger is designed for similar applications and installation as the standard Masonry Joist Hanger. The return adds additional lateral support by wrapping around the back of the masonry or timber. The hanger has a 25mm drop on the return flange as standard, but any variations can be made to order. Made from 2.4mm thick pre-Galvanised steel EN 10346 DX51D Z275. Also available in stainless steel.
Installation of 50x225mm R100mm Welded Return Hanger
- The back plate of the hanger should lie flat against the vertical masonry support.
- Masonry flange should have a minimum of 3 courses (675mm masonry) above.
- Both supporting and above masonry should be allowed to mature before any load is applied.
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm.
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent.
- To provide lateral restraint heavy duty straps should be used.
- The masonry flange should always be securely fixed or adequately embedded and should never be placed in dry slots.
- Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa.
- Use correct strength mortar as per British Standard.
Specification
- Galvanised steel EN 10346 DX51D Z275 or grade 1.4301 austenitic stainless steel to EN 10088-2.
- Manufactured to EN 845-1:2013.
- Tested by CERAM Research Ltd Notification Body No.1289.
Brand: TECO
Model and Size: PB13/19
Delivery Time: In stock, 1-2 days
Plaster depth 13-19mm uPVC Plaster Angle Beads are designed for use externally where galvanised bead cannot be used or where they are preferred to stainless steel. They are also used internally in high moisture content areas or where pro longed drying out periods may be necessary. An impac..
£4.18
£5.02 inc VAT
Brand: TECO
Model and Size: TCSS 63mm M16
Delivery Time: In stock, 1-2 days
Diameter: 63mmTeeth Size: 1.2mm63mm M16 Single Sided Tooth Plate Timber Connector is designed to improve bolt performance in timber joints. The connector's teeth must be embedded fully into the timber contact surface in order to achieve their design capacity. The connectors are p..
£0.73
£0.88 inc VAT
Brand: TECO
Model and Size: NP41x152
Delivery Time: In stock, 1-2 days
42x175mm Galvanised Nail Plate is plate used to connect or repair timber. The plate has strengthening ribs for added rigidity. All holes are pressed countersunk to aid location of the nail and to give a flush finish. Made from Galvanised steel EN 10346 DX51D Z275. InstallationUse appropria..
£46.74
£56.09 inc VAT
Brand: TECO
Model and Size: TFT50
Delivery Time: In stock, 1-2 days
50mm Timber Frame Ties are suitable for tying masonry outer cladding to softwood structural framework of domestic dwellings and industrial/commercial buildings up to 4 storeys and not greater than 15m in height. Suitable at a density of 4.4 ties per square meter for buildings anywhere in the South E..
£0.30
£0.36 inc VAT
Brand: TECO
Model and Size: CSHBZPM12x110
Delivery Time: In stock, 1-2 days
12mm - 110mm length Zinc Plated Coach Bolt. Cup Square Hex Bolts are also referred to as Coach Bolts or Carriage Bolts. They have a dome head with a square underneath for locking into the timber. Bright zinc plated or hot dipped spun galvanised to EN ISO 1461:2009 FeaturesSupplied com..
£17.86
£21.43 inc VAT
Brand: TECO
Model and Size: NUTFBZPM16
Delivery Time: In stock, 1-2 days
M16 Zinc Plated Hex Full Nuts for use with bolts and studding. InstallationAlways ensure that compatible corrosion resistant nuts & washers are used, i.e. do not use galvanised nuts & washers with stainless steel studding or vice versa...
£22.08
£26.50 inc VAT