375x375mm Gallows Bracket GB375 - pack of 2
375x375mm Gallows Bracket GB375 - pack of 2
Price: £36.94 (£44.33 inc VAT)
- Product Code: A1-5587
- Delivery Time: In stock, 1-2 days
- Brand: TECO
- Model and Size: GB375
- Weight: 6,000.00g
375x375mm Gallows Bracket GB375 - pack of 2
Width: 375mm
Height: 375mm
Weight: 6000g
Gallows Brackets provide support when removing an internal chimney breast. Painted - Red or Grey Primer. Supplied in pairs.
Specification
- Horizontal and vertical angle 50 x 50 x 5mm.
- 45 degree angle 25 x 25 x 3mm.
- Holed for M12.
- Finished in red Oxide Primer.
Installation
- The chimney breast is located on an external flank wall and no external projection exists.
- Where Gallows Brackets are not being used, then a steel beam (s) will be required. If there are load bearing walls either side of the chimney breast, then the Building Control Surveyor may be able to provide you with guidance on the type of beam and bearing which should be provided. In other cases a Structural Engineer should be employed to design a solution.
- Anchor fixings to be used with a minimum 100mm penetration into brickwork.
Please note that in general Gallows Brackets cannot be used if;
- The Wall to which they are to be fixed is less than 225mm thick, or
- The projection of the breast is more than 340mm (more than 150% of the thickness of the supporting wall), or
- The adjacent neighbours chimney breasts have already been removed or partially removed and gallows brackets installed, or
- The Brickwork or Mortar beds of the supporting walling are in poor condition.
Brand: TECO
Model and Size: HI200/3
Delivery Time: In stock, 1-2 days
Scrolled Hot Dipped Galvanised Hip Irons provide a decorative restraint when bedding hip tiles. Available in a range of sizes and finishes. InstallationDue to the angle of the roof along the hip, a Hip Iron is fixed at the bottom of the hip first to support the weight of the hip tiles so ..
£1.76
£2.11 inc VAT
Brand: TECO
Model and Size: WSQPBZPM12
Delivery Time: In stock, 1-2 days
M12 Bright Zinc plated Square Plate Washers are made from heavy duty hot dipped spun galvanised steel. Suitable for a variety of applications where a heavy washer is required. Thickness 3mm. InstallationAlways ensure that compatible corrosion resistant nuts & washers are used, i.e. do not u..
£17.50
£21.00 inc VAT
Brand: TECO
Model and Size: FHMR47X150R215
Delivery Time: In stock, 1-2 days
Masonry Return Joist Hanger is designed for similar applications and installation as the standard Masonry Joist Hanger. The return adds additional lateral support by wrapping around the back of the masonry or timber. The hanger has a 25mm drop on the return flange as standard. Any variatio..
£4.00
£4.80 inc VAT
Brand: TECO
Model and Size: DPC300
Delivery Time: In stock, 1-2 days
300mm Damp Proof Course - DPC provides damp proof protection, preventing ingress of external moisture. Suitable for brick, block, stone or concrete walls. Suitable for vertical and horizontal applications. Specification500mu.Produced to BS 6515:84.Suitable for withstanding a compress..
£10.09
£12.11 inc VAT
Brand: TECO
Model and Size: ERSS3
Delivery Time: In stock, 1-2 days
Stainless Steel External Render Stop Bead is predominantly used to form a neat bell shaped edge at the bottom of an external render finish, thus protecting the edge and acting as a runoff for when rainfall occurs. Use on traditional wet 2 or 3 coat plaster application. Galvanised product to be used ..
£4.91
£5.89 inc VAT
Brand: TECO
Model and Size: WM63x200
Delivery Time: 2 - 4 days
63mm x 200mm Welded Masonry Joist Hanger is designed to support 200mm high timber joist. The joist hanger's actual height is 190mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to ti..
£4.73
£5.68 inc VAT