490x375mm Gallows Bracket GB490 - pack of 2

490x375mm Gallows Bracket GB490 - pack of 2
Price: £55.76 (£66.91 inc VAT)
  • Product Code: A1-5588
  • Delivery Time: In stock, 1-2 days
  • Brand: TECO
  • Model: GB490
  • Weight: 7,560.00g

490x375mm Gallows Bracket GB490 - pack of 2

Width: 490mm
Height: 375mm
Weight: 7560g
Gallows Brackets provide support when removing an internal chimney breast. Painted - Red or Grey Primer. Supplied in pairs.
 
Specification
  • Horizontal and vertical angle 50 x 50 x 5mm.
  • 45 degree angle 25 x 25 x 3mm.
  • Holed for M12. 
  • Finished in red Oxide Primer.
Installation
  • The chimney breast is located on an external flank wall and no external projection exists.
  • Where Gallows Brackets are not being used, then a steel beam (s) will be required. If there are load bearing walls either side of the chimney breast, then the Building Control Surveyor may be able to provide you with guidance on the type of beam and bearing which should be provided. In other cases a Structural Engineer should be employed to design a solution.
  • Anchor fixings to be used with a minimum 100mm penetration into brickwork.
Please note that in general Gallows Brackets cannot be used if; 
  • The Wall to which they are to be fixed is less than 225mm thick, or
  • The projection of the breast is more than 340mm (more than 150% of the thickness of the supporting wall), or
  • The adjacent neighbours chimney breasts have already been removed or partially removed and gallows brackets installed, or
  • The Brickwork or Mortar beds of the supporting walling are in poor condition.

GB installGB install

Brand: TECO Model: WM44x250
Delivery Time: 2 - 4 days
44mm x 250mm Welded Masonry Joist Hanger is designed to support 250mm high timber joist. The joist hanger's actual height is 240mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to timber ..
£4.51
£5.41 inc VAT
Brand: TECO Model: WM90x150
Delivery Time: 2 - 4 days
90mm x 150mm Welded Masonry Joist Hanger is designed to support 150mm high timber joist. The joist hanger's actual height is 140mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to timber ..
£4.70
£5.64 inc VAT
Brand: TECO Model: HI300/5
Delivery Time: In stock, 1-2 days
Scrolled Hot Dipped Galvanised Hip Irons provide a decorative restraint when bedding hip tiles. Available in a range of sizes and finishes.  InstallationDue to the angle of the roof along the hip, a Hip Iron is fixed at the bottom of the hip first to support the weight of the hip tiles so that they ..
£3.09
£3.71 inc VAT
Brand: TECO Model: HD1200B100
Delivery Time: In stock, 1-2 days
Galvanised Heavy Duty Restraint Strap 1200mm Bent 100mm is designed for lateral and horizontal restraint (as in roof trusses). The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres holes.APP..
£3.58
£4.30 inc VAT
Brand: TECO Model: WT-275/250
Delivery Time: In stock, 1-2 days
275mm Stainless Steel Housing Tie offers a practical and cost effective solution for masonry cavity walls in box form domestic dwellings of up to a maximum 10m in height. Used for cavities from up to 150mm. Stainless Steel.Specification Fully tested to BS EN846-5:2000Meets the requirements of BS EN ..
£72.00
£86.40 inc VAT
Brand: TECO Model: TBFlange6x100
Delivery Time: In stock, 1-2 days
6x100 Flange Head Self Tapping Anchors for use in a variety of base materials. The self tapping action provides a positive anchorage in concrete, brick, stone and blocks. Zinc & Yellow Passivated.Length: 50mmDrill Dia: 6mmHole Depth Embedment: 10mmMax Fixture Thickness: 20mmClearance Hole (..
£48.31
£57.97 inc VAT