375x375mm Gallows Bracket GB375 - pack of 2
375x375mm Gallows Bracket GB375 - pack of 2
Price: £36.94 (£44.33 inc VAT)
- Product Code: A1-5587
- Delivery Time: In stock, 1-2 days
- Brand: TECO
- Model: GB375
- Weight: 6,000.00g
375x375mm Gallows Bracket GB375 - pack of 2
Width: 375mm
Height: 375mm
Weight: 6000g
Gallows Brackets provide support when removing an internal chimney breast. Painted - Red or Grey Primer. Supplied in pairs.
Specification
- Horizontal and vertical angle 50 x 50 x 5mm.
- 45 degree angle 25 x 25 x 3mm.
- Holed for M12.
- Finished in red Oxide Primer.
Installation
- The chimney breast is located on an external flank wall and no external projection exists.
- Where Gallows Brackets are not being used, then a steel beam (s) will be required. If there are load bearing walls either side of the chimney breast, then the Building Control Surveyor may be able to provide you with guidance on the type of beam and bearing which should be provided. In other cases a Structural Engineer should be employed to design a solution.
- Anchor fixings to be used with a minimum 100mm penetration into brickwork.
Please note that in general Gallows Brackets cannot be used if;
- The Wall to which they are to be fixed is less than 225mm thick, or
- The projection of the breast is more than 340mm (more than 150% of the thickness of the supporting wall), or
- The adjacent neighbours chimney breasts have already been removed or partially removed and gallows brackets installed, or
- The Brickwork or Mortar beds of the supporting walling are in poor condition.
Brand: TECO
Model: NP41x152
Delivery Time: In stock, 1-2 days
42x175mm Galvanised Nail Plate is plate used to connect or repair timber. The plate has strengthening ribs for added rigidity. All holes are pressed countersunk to aid location of the nail and to give a flush finish. Made from Galvanised steel EN 10346 DX51D Z275. InstallationUse appropria..
£46.74
£56.09 inc VAT
Brand: TECO
Model: NKG
Delivery Time: In stock, 1-2 days
30x3.75mm Galvanised Square Twist Nails are ideal for fixing Joist Hangers. The twisted shank gives greater pull out values than a standard round wire nail. Approx. 400 nails per kilo in a bag. Nail directly into timber...
£4.50
£5.40 inc VAT
Brand: TECO
Model: GTS - 76x300
Delivery Time: In stock, 1-2 days
76mm x 300mm Girder Truss Shoe is especially designed for supporting trussed rafters. The hanger is produced from 1mm thick pre-galvanised mild steel in accordance with the specification given in the BS EN 10327:2004 DX51D+Z275. The hanger includes a base tag which can significan..
£3.33
£4.00 inc VAT
Brand: TECO
Model: AR12
Delivery Time: In stock, 1-2 days
300mm Arris Rail Bracket is suitable for securing arris rails to a square fence post when building a feather edge fence or to repair a broken wooden arris rail to an existing post. Made from galvanised steel EN 10346 DX51D Z275.Installation &nbs..
£1.19
£1.43 inc VAT
Brand: TECO
Model: WNT - 100x277
Delivery Time: In stock, 1-2 days
100mm x 277mm Woody No Tag Joist Hanger is produced from 0.8mm thick pre-galvanised mild steel in accordance with the BS EN 10327:2004 DX51D+Z275 specifications. The hangers have been accordingly tested by Ceram Research, whereas the test results are available upon request.Also available in Stainles..
£0.60
£0.72 inc VAT
Brand: TECO
Model: WM125x200
Delivery Time: 2 - 4 days
125mm x 200mm Welded Masonry Joist Hanger is designed to support 200mm high timber joist. The joist hanger's actual height is 190mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to t..
£5.18
£6.22 inc VAT