47x125mm - R140mm Masonry Return Hanger
47x125mm - R140mm Masonry Return Hanger
Price: £3.76 (£4.51 inc VAT)
- Product Code: A1-5723
- Delivery Time: In stock, 1-2 days
- Brand: TECO
- Model and Size: FHMR47X125R140
- Weight: 478.00g
47x125mm - R140mm Masonry Return Hanger
Width: 47mm
Height: 125mm
Weight: 478g
Masonry Return Joist Hanger is designed for similar applications and installation as the standard Masonry Joist Hanger. The return adds additional lateral support by wrapping around the back of the masonry or timber. The hanger has a 25mm drop on the return flange as standard. Any variations can be made to order. Long term safe working load = 5.4 kN.
Features
- Pre-galvanized steel, 2.4mm thick,
- Galvanised steel EN 10346 DX51D Z600.
- Manufactured to EN 845-1:2013.
- Tested by CERAM Research Ltd.
Installation of 47x125mm - R140mm Masonry Return Hanger
- The back plate of the hanger should lie flat against the vertical masonry support.
- Masonry flange should have a minimum of 3 courses (675mm masonry) above.
- Both supporting and above masonry should be allowed to mature before any load is applied.
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm.
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent.
- To provide lateral restraint heavy duty straps should be used.
- The masonry flange should always be securely fixed or adequately embedded and should never be placed in dry slots.
- Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa.
- Use correct strength mortar as per British Standard
Masonry-Return-Hangers_data_sheet.pdf
Brand: TECO
Model and Size: LD600T100
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 600mm Twisted 100mm is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm..
£1.04
£1.25 inc VAT
Brand: TECO
Model and Size: WM90x150
Delivery Time: 2 - 4 days
90mm x 150mm Welded Masonry Joist Hanger is designed to support 150mm high timber joist. The joist hanger's actual height is 140mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to ti..
£4.45
£5.34 inc VAT
Brand: TECO
Model and Size: LL - 150x450
Delivery Time: In stock, 1-2 days
150x450mm Woody Long Leg Joist Hanger is produced from 1.5mm thick pre-galvanised mild steel produced in accordance to EN 10346 DX51D+Z275 with 50mm joist bearing. This timber to timber joist hanger designed for use in Loft Conversions where the hanger extends below the support...
£6.36
£7.63 inc VAT
Brand: TECO
Model and Size: SRTCSS 102mm
Delivery Time: In stock, 1-2 days
Diameter: 102mm102mm Stainless Steel Split Ring Timber Connector is designed for heavy shear loads in timber to timber connections.The Split Ring with the bevelled inside and outside face makes it easier to insert in the pre-cut grooves and also gives greater load capacity.The Ring is..
£20.73
£24.88 inc VAT
Brand: TECO
Model and Size: PB13/19
Delivery Time: In stock, 1-2 days
Plaster depth 13-19mm uPVC Plaster Angle Beads are designed for use externally where galvanised bead cannot be used or where they are preferred to stainless steel. They are also used internally in high moisture content areas or where pro longed drying out periods may be necessary. An impac..
£4.18
£5.02 inc VAT
Brand: TECO
Model and Size: WSTDGM24
Delivery Time: In stock, 1-2 days
Diameter: 44mm M24 Standard Round Washers are made from heavy duty hot dipped spun galvanised steel. Suitable for a variety of applications where a heavy washer is required. InstallationAlways ensure that compatible corrosion resistant nuts & washers are used, i.e. do not use galv..
£8.50
£10.20 inc VAT