47x100mm - R140mm Masonry Return Hanger
47x100mm - R140mm Masonry Return Hanger
Price: £3.56 (£4.27 inc VAT)
- Product Code: A1-5718
- Delivery Time: In stock, 1-2 days
- Brand: TECO
- Model and Size: FHMR47X100R140
- Weight: 428.00g
47x100mm - R140mm Masonry Return Hanger
Width: 47mm
Height: 100mm
Weight: 428g
Masonry Return Joist Hanger is designed for similar applications and installation as the standard Masonry Joist Hanger. The return adds additional lateral support by wrapping around the back of the masonry or timber. The hanger has a 25mm drop on the return flange as standard. Any variations can be made to order. Long term safe working load = 5.4 kN.
Features
- Pre-galvanized steel, 2.4mm thick,
- Galvanised steel EN 10346 DX51D Z600.
- Manufactured to EN 845-1:2013.
- Tested by CERAM Research Ltd.
Installation of 47x100mm - R140mm Masonry Return Hanger
- The back plate of the hanger should lie flat against the vertical masonry support.
- Masonry flange should have a minimum of 3 courses (675mm masonry) above.
- Both supporting and above masonry should be allowed to mature before any load is applied.
- Joist should be square cut and sit tight to the back of the hanger - maximum gap permitted is 6mm.
- Nail the side flanges with 30 x 3.75mm galvanised square twist nails or equivalent.
- To provide lateral restraint heavy duty straps should be used.
- The masonry flange should always be securely fixed or adequately embedded and should never be placed in dry slots.
- Always ensure that compatible corrosion resistant fixings are used, i.e. do not use galvanised fixings with stainless steel products or vice versa.
- Use correct strength mortar as per British Standard
Masonry-Return-Hangers_data_sheet.pdf
Brand: TECO
Model and Size: HM900
Delivery Time: In stock, 1-2 days
Galvanised Hex mesh Netting is used for floor screed reinforcement, wall plaster reinforcement and roof insulation. Also can be used for fencing. Made from hot dipped galvanised steel prior to weaving. Gloves should be worn as edges will be sharp.Hex mesh is formed by twisting two adjacent wires at ..
£52.73
£63.28 inc VAT
Brand: TECO
Model and Size: WT-225/50
Delivery Time: In stock, 1-2 days
225mm Stainless Steel Housing Tie offers a practical and cost effective solution for masonry cavity walls in box form domestic dwellings of up to a maximum 10m in height. Used for cavities from 50mm to 70mm. Stainless Steel.Specification Fully tested to BS EN846-5:2000Meets the requirement..
£9.69
£11.63 inc VAT
Brand: TECO
Model and Size: TFT100
Delivery Time: In stock, 1-2 days
100mm Timber Frame Ties are suitable for tying masonry outer cladding to softwood structural framework of domestic dwellings and industrial/commercial buildings up to 4 storeys and not greater than 15m in height. Suitable at a density of 4.4 ties per square meter for buildings anywhere in the South ..
£0.43
£0.52 inc VAT
Brand: TECO
Model and Size: WSS4x40
Delivery Time: In stock, 1-2 days
4x40mm Stainless Steel Wood screws - ideal for fixing stainless steel brackets and stainless steel mesh products when used with a stainless steel 18mm diameter washer. Grade 1.4301 austenitic stainless steel to EN 10088-2. Screw directly into timber using a small pilot hole if require..
£23.40
£28.08 inc VAT
Brand: TECO
Model and Size: FHMR47X100R140
Delivery Time: In stock, 1-2 days
Masonry Return Joist Hanger is designed for similar applications and installation as the standard Masonry Joist Hanger. The return adds additional lateral support by wrapping around the back of the masonry or timber. The hanger has a 25mm drop on the return flange as standard. Any variatio..
£3.56
£4.27 inc VAT
Brand: TECO
Model and Size: WM44x275
Delivery Time: 2 - 4 days
44mm x 275mm Welded Masonry Joist Hanger is designed to support 275mm high timber joist. The joist hanger's actual height is 265mm, and the flange is built into brick or block wall. It has a minimum crushing strength of 3.5N/mm. Welded Masonry Joist Hanger is also suitable for many timber to ti..
£4.49
£5.39 inc VAT