490x375mm Gallows Bracket GB490 - pack of 2
490x375mm Gallows Bracket GB490 - pack of 2
Price: £55.76 (£66.91 inc VAT)
- Product Code: A1-5588
- Delivery Time: In stock, 1-2 days
- Brand: TECO
- Model and Size: GB490
- Weight: 7,560.00g
490x375mm Gallows Bracket GB490 - pack of 2
Width: 490mm
Height: 375mm
Weight: 7560g
Gallows Brackets provide support when removing an internal chimney breast. Painted - Red or Grey Primer. Supplied in pairs.
Specification
- Horizontal and vertical angle 50 x 50 x 5mm.
- 45 degree angle 25 x 25 x 3mm.
- Holed for M12.
- Finished in red Oxide Primer.
Installation
- The chimney breast is located on an external flank wall and no external projection exists.
- Where Gallows Brackets are not being used, then a steel beam (s) will be required. If there are load bearing walls either side of the chimney breast, then the Building Control Surveyor may be able to provide you with guidance on the type of beam and bearing which should be provided. In other cases a Structural Engineer should be employed to design a solution.
- Anchor fixings to be used with a minimum 100mm penetration into brickwork.
Please note that in general Gallows Brackets cannot be used if;
- The Wall to which they are to be fixed is less than 225mm thick, or
- The projection of the breast is more than 340mm (more than 150% of the thickness of the supporting wall), or
- The adjacent neighbours chimney breasts have already been removed or partially removed and gallows brackets installed, or
- The Brickwork or Mortar beds of the supporting walling are in poor condition.
Brand: TECO
Model and Size: MMINI - 44x68
Delivery Time: In stock, 1-2 days
44x68mm Mini Mini Joist Hanger is a timber to timber joist hanger suitable for light duty applications such as trimmers, ceiling joists and decking. The hanger is produced from 1mm thick pre-galvanised mild steel. The tag on the base of the hanger helps avoid rotation and aids fast, accurate lo..
£0.53
£0.64 inc VAT
Brand: TECO
Model and Size: WSQPBZPM16
Delivery Time: In stock, 1-2 days
M16 Bright Zinc plated Square Plate Washers are made from heavy duty hot dipped spun galvanised steel. Suitable for a variety of applications where a heavy washer is required. Thickness 3mm. InstallationAlways ensure that compatible corrosion resistant nuts & washers are used, i.e. do not u..
£17.50
£21.00 inc VAT
Brand: TECO
Model and Size: TDS75
Delivery Time: In stock, 1-2 days
75mm Timber Drive Screw is a heavy duty fixing that requires no pre-drilling. Suitable for many timber to timber applications. Features 7mmHeat treated shank for extra strength. Green organic coating. Each pack comes complete with driver.InstallationScrew directly into timber, no pre dril..
£9.35
£11.22 inc VAT
Brand: TECO
Model and Size: LD750T100
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 750mm Twisted 100mm is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm..
£1.30
£1.56 inc VAT
Brand: TECO
Model and Size: LD220F
Delivery Time: In stock, 1-2 days
Galvanised Light Duty Restraint Strap 220mm Flat is designed for vertical restraint, for example fixing wall plates to masonry. The straps are produced from edge coated galvanised mild steel, also available in stainless steel. They are designed for 6mm and 25mm offset centres hol..
£0.53
£0.64 inc VAT
Brand: TECO
Model and Size: PB13/19
Delivery Time: In stock, 1-2 days
Plaster depth 13-19mm uPVC Plaster Angle Beads are designed for use externally where galvanised bead cannot be used or where they are preferred to stainless steel. They are also used internally in high moisture content areas or where pro longed drying out periods may be necessary. An impac..
£4.18
£5.02 inc VAT